Новости

No more cables, and connectors to Your desk by using the new accessory for TEK-BERRY developed by TEKO that allows to operate at a tidy workstation! The RPI-VESA adapter perfectly suits to the standard VESA 50, 75 and 100 and ensures compatibility with most of the screens on the market.

Easy to install by means of 4XM4-countersunks screws (not included). The simple fixing  system allows to firmly hold Your Raspberry-PI into our TEK-BERRY case.

Minimal designed and completely transparent, the RPI-VESA Adapter can be perfectly used as wall bracket, ideal for industrial applications (home automation, IT-technology, security systems etc.).

 The benefits of using our RPI-VESA:

• significant reduction of the cables from Your desk
• no danger of liquids or dirt falling on your Raspberry-PI
• high visual impact
• simple and intuitive system for fixing and dismounting with the TEK-BERRY
• suitable for standard VESA50, VESA75 and VESA100

• possibility of mounting on all types of surfaces (wall, desktop, Rack cabinets, etc.)

As we know, the Raspberry Foundation offered the possibility to  maximize the performances of Raspberry-PI Rev. 2 by providing  a 512M-RAM and by overclocking up to 1GhZ without affecting  the warranty: http://www.raspberrypi.org/archives/2008

This inevitably leads to a substantial increase of the temperature of the main components and a consequent reduction in lifetime of the board.To overcame this problem, TEKO has developed a cooling kit which allow to reduce the temperature. The kit consists of three heat sinks to apply directly on the SOC (BMC2835), on the USB/Ethernet (LAN 9512) and on the regulator voltage by means of the 3M thermal adhesive included in the kit.

The tests we did with thermal chamber by playing the QUAKE-3 DEMO , show a strong reduction of the temperature up to 12°C.

Without RPI-COOLKIT		With RPI-COOLKIT

The benefits of using our KIT:

• easy assembling assured by the 3M adhesive tape
• extremely low profile to an easy access to GPIO
• compatible with Raspberry PI Rev-1 and Rev-2
• no noisy funs
• extension of life of your Raspberry PI

• reduction of failure risk

Now fully compatible with Raspberry PI Rev1 and Rev2

Multifunction flat enclosure, modern designed, ideal for desktop, hand-held and wall mounting applications. Wide recessed area on the top part suitable for touch-screen displays up to 10” (204,5x158,5mm). This model is equipped with IP65 sealing kits for screws and case. Internal battery compartments on both sides to accept 2+2 1,5V mignon cells (AA). Internal bosses on top and bottom for an easy fixing of the PCB. Closing by four M3 screws.

New models from TEKNET series featuring a “T-shape”. ABS hand-held enclosures with elastomer grips (TPU) on the sides. Matt surface finishing. The recessed area on the cover is suitable to accept a keypad membrane. Internal pillars on top and bottom to fix PCB. Closing by four screws.

Extruded aluminium enclosures with high quality black powder coating. Internal slots for easy setup of boards. All models are equipped with IP65 sealing kits. The versions with “E” have front panels equipped with built-in flanges for wall mounting. The “TEKAM 5L” series consists in two half extruded profile, snap-on closing allowing to fix panel mounting components. Closing by eight screws.

Extruded aluminium enclosures with high quality black powder coating. Internal slots for easy setup of boards. All models are equipped with IP65 sealing kits. The versions with “E” have front panels equipped with built-in flanges for wall mounting. Closing by eight screws.

Extruded aluminium case with powder coating and two rubber sealing kits to protect against water and from dust (IP65) available in six different colours. Two metal front panels, internal slots for PCB’s and a recessed area for a keypad membrane. The models with “E” have mounting wall metal panels. The “TEKAM 3L” series consists in two half extruded profile, snap-on closing allowing to fix panel mounting components. Closing by four or eight screws.

The TEK-BERRY case suitable to house the Raspberry PI board, is now available in different colors…

The TEK-BERRY assortment is on stock.  You can buy this case at:

Allied Electronics

More than 50 years dedicated to the design and manufacture of standard enclosures for the Electronics have led to the creation of the first professional case specific for housing the Raspberry Pi™*.
The distinctive design made in Italy reveals a detailed analysis of the characteristics that the case must have to match the potential of this innovative device.
Distinguishing mark of our case than any existing homebrews is that our project is based on a real board and not on drawings available in the world wide web. The result is a perfect assembly of the board and of all the connections.

Now available on stock!

International sales through TEKO Worldwide distributor

* Raspberry Pi is a trademark of the Raspberry Pi Foundation

TEKO is pleased to annouce new opportunities You have through the Reserved Area in our Web site.
 
Besides Your Company details, that you can verify at every time, check the price list and the availability at stock of TEKO items , now you can also:
 
- send Purchase orders and/or request for quote 
- check the status of an order
 
We recall that You get the access to the Reserved Area by entering your customer code in the field USERNAME
The customer number is  printed on all offers, order confirmations, Delivery notes (DDT) and shipping invoices.

TEKO introduces a new model in the TEKMAG range with different dimensions. Hand-held enclosure , moulded in TEKNIUM®, a special magnesium alloy, that will convince You thanks to the ultra-light weight, the absolute strength, and the shielding properties of the three models available. The side profiles have a special black soft-feel surface to assure a secure grip. The model is equipped with IP67 sealing kits. The versions with “B” have a battery compartment for two 1,5 mignon cells (AAA) while the models with “B2” have a battery compartment for four 1,5V mignon cells (AAA). The recessed area on the covers can accept a keypad membrane or a LCD display. Closure by four screws. Two-tone colour version: Graphite grey /Black RAL 9004.

Series of small anodized aluminium enclosures with multi-shot moulded (ABS+TPU) two-tone coloured front cover panels. They have co-moulded sealing to protect against water and from dust (IP65). The internal guides allow an easy assembly of PCB. Closing by eight screws.

New models from TEKNET series featuring an increased height. ABS hand-held enclosures with elastomer grips (TPU) on the sides. Matt surface finishing. The recessed area on the cover is suitable to accept a keypad membrane or an aluminium panel. The models with “B” have a battery compartment for one 9V Battery (PP3) or two 1,5V cells (AA). The models with “B2” have a battery compartment for two 9V batteries (PP3) or four 1,5V cells (AA). Closing by four screws. Upon request, aluminium panel “APTB”; standard keypad membrane “M”, “MW”, “M58”, “M59”.

Rectangular rings especially designed as accessories for the “WITEK”-Series and developed to improve protection from powder and against water. They are available in seven different colours to obtain a tailor-made solution reflecting the identity of customer or application. From quick and easy assembly, they fit perfectly all around the closed box.

Attractive and modern designed, this box is moulded in transparent metacrylate. It holds twenty tubes with a height of 25 mm or of 40 mm, ideal to store and organise small electronic components.

Extruded aluminium case with powder coating and two rubber sealing kits to protect against water and from dust (IP65) available in six different colours. Two metal front panels, internal slots for PCB's and a recessed area for a keypad membrane. The models with "E" have mounting wall metal panels. Closing by four or eight screws.

Ergonomic designed ABS pocket enclosures with one, two or three push-buttons,available in six different colours, configuration. Space for round PCB (35 mm.) with button cells batteries. The model "OVO-3/0" has no buttons. Matt surface finish. Simple interlocking assembly.

Small enclosure with ergonomic design, moulded in two materials, using multi-shot injection.Four models available, from one to four push buttons figuration. Protection class up to IP 65. Base with integral PCB mounting studs. Closing by two screws. Two-colours combination: Grey RAL 7046/ Black RAL 9004 . Applications: transmitters, personal security, home automation.

Series of enclosures moulded in two-materials (ABS/PC and TPU) with snap-on closing. Base with integral mounting studs for PCB. Two combinations of colours available: Black RAL 9004/Dark grey RAL 7012 - White RAL 9002/Light grey RAL 9018.

ABS Hand-Held enclosure with soft-touch elastomer grips (TPU) on the side. Matt surface, recessed area for membrane keyboard or displays. The models with "B" have a battery compartment for two 1,5V mignon cells (AA) or one 9V battery (PP3). The models with "B2" have a battery compartment for four 1,5V mignon cells (AA) or two 9V batteries. Closing by four screws. Two combinations of colours: Black RAL 9004/Dark grey RAL 7012 - White RAL 9002/Light grey RAL 9018.

Inclined extruded aluminium case with high quality painted finishing. Two ABS side panels, internal guides for PCB, recessed area for membrane keypad.Closing by six screws. Two colours combinations: black RAL 9004 / grey RAL 7012 - white RAL 9002 / light grey RAL 9018. Upon request wall-suspension element "MT7.0".

Teko is pleased to introduce an innovative range of enclosures that represent a real revolution in the field of enclosures for electronic applications. Through the standard products, our Company always offers high performance cases. Now, we are presenting on the market for the first, the new TEKMAG range of cases, moulded in TEKNIUM®, a special magnesium alloy, that will convince You thanks to the ultra-light weight, the absolute strength, and the shielding properties of the three models available. Due to the unique design, TEKMAG cases are mostly suitable for hand-held devices in the industrial automation, avionics, marine and automotive fields. Never before, a metallic hand held enclosure has been optimized to be used in such high-tech applications. No compromises no longer with TEKMAG models! New perspectives are now available to wear Your projects. All models are equipped with IP67 sealing kits, to protect your electronics against water and powder. The side profiles have a special soft-feel surface to assure a secure grip. Versions with battery compartment for 2x AA / 1x 9V batteries or 4x AA / 2x 9V batteries suitable for self-powered devices are available. The recessed area 132 x 72 mm on the covers can accept a keypad membrane or a LCD display.

Circular shaped storage box moulded in transparent methacrylate, equipped with 10 sections to store and organise small electronic components.

ABS enclosure with matt surface finish. Model MOK1 has a recessed area for keypad membrane or display. Base and cover have integral mounting studs for PCB. The bottom is manufactured by transparent Bayblend® and it is suitable for fixing on a 2 / 6-module standard box 503. Snap-on closing.

ABS enclosure with matt surface finish. On front side, 1,8 mm recessed area for keypad membrane or display. Base and cover have integral mounting studs for PCB. The bottom is manufactured by transparent Bayblend® and it is suitable for fixing on a 2 / 6-module standard box 503. Snap-on closing.

WALL SUPPORTS

Extruded aluminium case with powder coating and two rubber sealing kits to protect against water and from dust (IP65) available in six different colours. Two metal front panels, internal slots for PCB's and a recessed area for a keypad membrane. The models with "E" have mounting wall metal panels. Closing by four or eight screws.

Compact extruded anodised aluminium enclosures. Two aluminium front cover panels with two rubber sealing kits to protect against water and from dust. Internal slots for PCB's. Closing by eight screws.

Extruded aluminium case with powder coating. Two wall mounting ABS panels. The model with "-B" has a battery compartment for two 1,5V (AA) or one 9V (PP3). All the models are closed by four screws.

ABS enclosure with new soft-touch contoured shape. By utilising multi-shot moulding technology, the MINITEKNET features an ergonomic design of elastomer grips (TPU) on the side of the case. Battery compartment for two 1,5V (AA) mignon cells or one 9V flat battery (PP3). Base and cover have integral PCB mounting studs. Matt surface finish. Closing by four screws.

ABS enclosures with new soft-touch contoured shape. By utilising multi-shot moulding technique, Teknet features an ergonomic design of elastomer grips (TPU) on the side of the case. The models with "-B" have a battery compartment for two 1.5V mignon-cells (AA) or one 9V flat battery (PP3). The models with "-B2" have a battery compartment for four mignon cells 1,5V (AA) or two flat batteries 9V (PP3). Matt surface finish. Closing by four screws. Upon request aluminium panel "APTB", Keypad membrane "M" or "MW" (with transparent display area).

Ergonomically shaped ABS enclosures, especially designed for use as hand-held instruments enclosures. The Model "OK-2" has on the cover a recessed area suitable for a keypad membrane or a wide screen 4,3 " TFT Display. The models with "-B" have a battery compartment for two 1,5V (AA) or one 9V flat battery (PP3) while the models with "B2" have a battery compartment for four 1,5V (AA) or two 9V flat batteries (PP3). Matt surface finish. Closing by four screws.

ABS enclosure with rounded corners. Base and cover have integral PCB mounting studs. They are moulded in white and transparent blue. Matt surface finish. Closing by one screw.

WALL SUPPORTS